購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
畢業設計（論文）文件清單
畢業設計（論文）題目： 定位支座數控加工夾具設計
姓名： 江本恒 班 級： 機自07-1
編號
名稱
件數
頁數
1
畢業設計（論文）說明書
2
畢業
設計
（論文）附件
畢業設計（論文）任務書
3
畢業設計（論文）開題報告
4
畢業設計（論文）工作計劃
5
文獻綜述
6
外文文獻翻譯
7
畢業設計（論文）工作總結
8
圖
紙
A0
9
A1
10
A2
11
A3
12
A4
13
電子文檔
14
其
它
畢業設計（論文）選題報告
15
畢業設計（論文）指導記錄
16
畢業設計（論文）中期檢查表
備
注
大連水產學院本科畢業論文（設計）
目 錄
摘要………………………………………………………………………………………………Ⅴ
Abstract…………………………………………………………………………………………Ⅵ
前言…………………………………………………………………………………… 1
1 零件的用途……………………………………………………………………………………2
1.1 計算零件生產綱領 確定零件的加工類型……………………………… 2
1.2 研究分析被加共零件圖和被加工零件的原始資料，審查改善零件的結構工藝性。…………………… …………… …………… …………………………2
1.3毛坯種類的選擇………………………………………………………………………3
1.4零件毛坯的工藝性分析……………………………………………………………3
2 數控加工工藝分析…………………………………………………………5
2.1零件介紹…………………………………………………………………5
2.2數控加工工藝的合理性分析……………………………………………5
2.3數控加工工藝的特點……………………………………………………5
2.3.1 數控加工的一般特點……………………………………………5
2.3.2數控加工工藝的特殊要求……………………………………… 6
2.4 零件的工藝性分析………………………………………………………6
2.4.1零件圖樣的具體工藝分析………………………………………7
2.5數控加工工藝過程的擬定………………………………………………9
2.5.1 工序順序安排的一般原則………………………………………… 9
2.5.2工步順序安排的一般原則…………………………………………………… 9
2.6進給路線的確定…………………………………………………………10
2.6.1確定進給路線的主要原則……………………………………… 10
2.7工件的裝夾………………………………………………………………10
2.7.1定位基準選擇的一般原則………………………………………………10
2.7.2工件定位方案……………………………………………………………10
2.8切削用量的確定…………………………………………………………11
2.8.1背吃刀量的確定……………………………………………………11
2.8.2主軸轉速的確定……………………………………………………12
2.8.3進給速度的確定……………………………………………………12
2.9加工刀具的選擇…………………………………………………………13
2.9.1選擇數控刀具通常應考慮的因素…………………………………13
2.9.2面銑刀主要參數的選擇……………………………………………13
2.9.3鉆孔刀具及其選擇…………………………………………………14
2.9.4鏜孔刀具及其選擇…………………………………………………14
3 工藝規程的制訂…………………………… ………… ………………………16
3.1零件的工藝性分析…………………………………………………………16
3.1.1工序10………………………………………………………………16
3.1.2工序20………………………………………………………………16
3.1.3工序30………………………………………………………………16 3.1.4工序40………………………………………………………………16 3.1.5工序50………………………………………………………………17 3.1.6工序60………………………………………………………………17
3.1.7工序70………………………………………………………………17
總 結…………………………………………………………………………… 19
致謝……………………………………………………………………………… 20
參考文獻…………………………………………………………………………21
摘 要
本論文主要研究的是不規則零件在現代制造業中的廣泛應用，那么保證此類零件的加工精度就顯得尤為重要。本課題通過分析定位支座零件的結構特點和加工要求，用數控加工中心來達到多工位的加工目的,提高零件在大批量生產制造過程中的效率,同時制定了一套較為合理加工工藝規程，從而為保證該零件的加工精度將提供一種經濟實用的夾具設備，具有一定的實用價值，在論文中會以研究零件的工藝規程開始著手設計最為適合的夾具，在不同的夾緊方案下進行比較，并且以平面加工為定位方法，通過夾緊力的計算和定位誤差達到比較，選則最為恰當、最為合理的夾具設計方案，從而保證了被加工零件的精度以及工件在加工過程中定位的可靠和準確，夾具提供足夠大的夾緊力以防止工件位移，工件在夾緊力的作用下形變小。從而使得夾具在裝夾工件進行加工的過程中正真發揮其作用,提高勞動的生產效率、具備一定的實用價值。
關鍵字：夾具裝夾，定位，加工精度，平面加工,多工位
ABSTRACT
This paper is a study of irregular parts in the modern manufacturing a wide range of applications, then ensure that such parts of the machining accuracy is particularly important. Positioning the subject by analyzing the structure of parts bearing the characteristics and processing requirements to achieve the CNC Machining Center multi-purpose processing, high-volume production parts to improve manufacturing process efficiency, while more reasonable to develop a set of processing a point of order, so as to ensure that the machining accuracy will provide an economical and practical equipment of the fixture has a certain practical value, in the paper will be to study the parts of the process started to design a point of order most suitable for the fixture,
In different comparison under clamping and positioning with planar processing method for the calculation of clamping force and position error to compare the election is the most appropriate and most reasonable design of the jig, thus ensuring the accuracy of parts processed and the workpiece during processing of reliable and accurate positioning, fixtures provide the clamping force is large enough to prevent displacement of the workpiece, the workpiece clamping force in the role of small deformation. So that the workpiece clamping fixture for processing in the process of Chiang Kai-shek really play its role in enhancing the productivity of labor, have a certain practical value.
Keywords: Fixture clamping, positioning, machining accuracy, planar processing, multi -
VI
DFU-07-414：
大連水產學院畢業設計（論文）教師選題報告表
課題名稱
定位支座數控加工夾具設計
課題性質
真實
課題類型
數控
課題來源
生產
指導教師姓名
李剛
年 齡
職稱（學位）
講師
所在單位
數控教研室
從事專業
數控教研
聯系電話
課題簡介：（主要內容、目前研究現狀、意義、需要條件、時間安排、預期成果及表現形式。）
畢業設計是培養學生實踐能力的重要環節之一，并進行了專門的生產實習，它是對我們大學所學課程的綜合檢驗。在學習過程中老師以理論與生產實踐相結合的教學方式，因此在此次畢業設計中要求我們?nèi)婢C合地運用所學課程的理論和實踐知識進行零件加工工藝規程的設計。其目的在于：
（1）培養我們運用機械制造工藝學，數控加工工藝及有關課程（工程材料與熱處理、機械設計、公差與測量技術、金屬切削原理與刀具、數控機床自動編程等）的知識。獨立地分析和解決工藝問題。初步具備設計一個中等復雜程度零件的工藝規程的能力。
（2）能根據被加工零件的技術要求運用夾具設計的基本原理和方法，學會擬定夾具設計方案，完成夾具結構設計，提高結構設計能力。當然，夾具設計不在本次設計范圍內！
（3）培養我們熟悉并運用有關手冊，圖表等技術資料的能力。
（4）進一步培養我們識圖，制圖，運算和編寫技術文件等基本的技能。
（5）更更重要的是培養了我們嚴肅認真，一絲不茍和實事求是的工作作風，從而實現從學生到工程技術人員的過渡設計。
共計安排15周時間：
第 1～2 周 實習調研、查閱資料第5～13周 上機運算（繪圖）
第 3～4 周 方案確定、開題報告第5～13周 設計計算（實驗）
第 14 周 撰寫說明書（論文） 第 15 周 上交設計（論文）
指導教師簽名： 教研室意見： 日期：2009.1
學院（系）畢業論文（設計）領導小組意見：
組長簽字： 日期：
教務處制表
大連水產學院
畢業設計(論文)任務書
2009屆 職業技術學院 機械設計制造及其自動化專業
題目： 定位支座數控加工夾具設計
子題：
學生姓名： 江本恒 班 級： 機自07-1
指導教師(簽章)： 李剛 職稱（學位）： 講師
所在教研室： 數控教研室
專業負責人(簽章)：
下達日期：2009 年 2月26日 完成日期：2009 年 6月13日
題目性質
真實
題目類型
設計
題目來源
生產
課題簡介
定位支座數控加工夾具設計。它是在生產與實踐教學模式的基礎上結合企業的實際情況針對一個中等復雜零件的機械加工工藝規程的畢業設計綜合性，使用性，和實踐性較強的設計過程
具體任務、內容及要求（包括設計計算、實驗分析、繪圖質量各類圖紙張數、外文翻譯及撰寫外文摘要等要求）
設計條件和原始數據：
1、定位支座樣品1件；
2、機床加工成型；
3、產量500件（小批量）；
4. 機械加工工藝卡片一套；
5 零件圖一張。
設計的主要內容及要求：
1、繪制夾具的零件圖和裝配圖；
2、繪制夾具結構總裝草圖；
3、用CAD軟件繪制夾具的總裝配圖；
4、重要夾具零件圖和造型；
5、編寫夾具中一個成型零件的加工工藝卡片；
6、編寫一本不少于10000字的設計說明書；
7、撰寫1500字以上的文獻綜述；
8、獨立翻譯一篇3000字以上、與課題相關的外文參考文獻；
9、除夾具草圖外，其余所有設計內容均由計算機及相應軟件形成電子文檔并打印和手工繪制；
10、繪圖量不少于折成A0號圖紙4張；
11、參考文獻不少于10篇。
確定選題、撰寫開題報告、調研
第1~2周
編寫設計說明書
第14周
撰寫文獻綜述、翻譯外文文獻、確定總體方案
第3~4周
審閱畢業設計
第15周
設計計算、作圖等
第5~13周
畢業答辯
第16周
畢業論文（設計）領導小組長簽章：
教務處制表
781型銑邊機維修
跳針是銑邊機經常出現的故障，跳針可分為：下勾線盤勾線跳針和機針未勾上縫線跳針。
??? 下勾線盤勾線跳針
如何判斷是下勾線盤勾線跳針呢？在操作中上勾線鉤勾住機針線環，機針帶著縫線下降，下勾線盤勾線后，這時縫料上面或線鉤上有線環，這都是因為下勾線盤鉤頭沒有勾住機針上的線環所造成的跳針。調整時機針高度的定位標準是：機針在上死點時機針尖距離針板上平面16mm。下勾線盤的勾線時間為：機針在第一圈下降至下死點后，向上回升1.3 mm時，下勾線盤鉤頭應該到達機針凹面中心（圖1），鉤頭與機針凹面的間隙為零。在這里要強調的是通常情況下機針回升1.3 mm時，下勾線盤鉤頭應到達機針中心。這是因為針桿下降至針板時封針被擋在了針板上方（圖2、3），機針孔向操作者的一面打開，針孔內的縫線失去了保護，機針從下死點稍微向上回升，機針孔內的縫線失去拉力很容易形成線環，如果下勾線盤勾線時間略遲，在勾線之前縫線就容易從機針孔內脫出或線環過大扭曲變形造成跳針。也可將下勾線盤勾線時間稍微提前。
?
??? 機針勾線跳針
機針勾線跳針表現為：在縫制面料的正面一針或幾針沒有線跡，或縫了幾針后機針再也帶不上縫線。要排除該故障，首先應對機器的下送線機構有所了解，弄清它的工作原理、時間相位。
機針在第一圈的下死點，當回升1.3 mm時下勾線盤鉤頭勾住機針線環，并繼續旋轉擴大線環（圖4、5），依次將縫線送入下送線指內→緊線鉤中→夾線器中。與此同時，下送線鉤從前行程末端，向后（操作者）擦著縫線運動到后行程末端，然后勾著縫線再運動到前行程末端停止。第二圈沒有帶縫線的機針下降至下死點后開始回升，此時下送線指推著縫線同步向左前方圍著機針作曲線運動，下送線指和機針相遇時的距離為0.1 mm（圖4），在機針上升至封針封住機針孔后，下送線指開始回退，緊線鉤松線，夾線器打開。
要保證機針能順利地勾上縫線，那么縫線每次都應在下送線鉤前、下送線指內、夾線器中、緊線鉤內。重要的是下送線鉤必須每次把縫線勾住，這就要求必須調整好它們的時間相位。調整時最好用觀察針板（把針板右邊磨掉一部分），以便于觀察下勾線盤勾線、下送線鉤勾線和送線、送線指的送線情況。下送線鉤在機針前行程末端時的標準位置是：下送線鉤和機針的距離是2.5 mm。下送線鉤在左面的標準位置是：下送線鉤鉤頭超出機針左邊0.3 mm。旋松下送線鉤座固定螺釘進行調節（圖6）。下送線鉤的高度距離針板下面0.3 mm（圖7），旋松下送線鉤緊固螺釘進行調節。為什么要距離針板這么近，主要是因為下送線鉤越高，下送線鉤就越容易擦著縫線向后運動，返回時就能勾住縫線。機針勾線跳針，絕大部分都是由于下送線鉤沒有勾住縫線所造成的。下送線鉤的弧型背面擦著縫線向后運動，然后勾上縫線送向前行程末端，這一點尤為重要。還要注意的一點是，在縫制過程中出現斷針，在排除故障前，最好先檢查下送線鉤弧型背面有無劃傷，如果下送線鉤弧型背面有毛刺，那么當下送線鉤向后運動，縫線就不可能順暢地滑入下送線鉤的前面，下送線鉤也就沒有勾住縫線，跳針也就很自然的事。
夾線器調整不當，也會引起機針勾線時偶爾跳針。它的時間相位是：在第一圈下勾線盤勾住機針線環旋轉擴大，緊線鉤和夾線器的左半邊在下勾線盤鉤頭前8 mm左右，開始進入下勾線盤內。在第二圈當回升的機針勾住縫線并被封針封住針孔后，緊線鉤松線，夾線器打開。調整方法是：旋松夾線器控制凸輪上的兩顆緊固螺釘進行調整（圖8），但調整后還應觀察下送線鉤的送線時間相位是否正確。這是因為下送線鉤控制凸輪和夾線器控制凸輪是連接在一起的，如果下送線鉤時間相位受到影響，就應拆下下勾線盤，在夾線器控制凸輪槽內用扳手旋松兩顆緊固螺釘，用六方扳手帶著其中一顆螺釘在槽內滑動，從而改變下送線鉤的時間相位。
??? 末尾線頭長
理想的末尾線頭長是10cm左右，超過就可以認為末尾線頭過長，造成縫線浪費。線頭長的主要原因是下送線鉤調整的位置不當和下勾線盤沒有調到標準位置?？傊肽┪簿€頭短，下送線鉤寧高勿低，下勾線盤勾線時間寧早勿遲。
??? 縫線散開、起絲和斷線
縫線起絲主要是由于下送線指送線和夾線器松線的時間過早所致。調整方法是調整它們各自的控制凸輪的時間相位。標準的時間相位如圖4，機針從下死點回升，下送線指同步送線，封針封住機針孔后，送線指開始回退，夾線器開始張開松線。另外還可以通過夾線器調節螺釘，改變縫線的張力大?。▓D5），下勾線盤鉤頭內若卡上縫線或鉤頭內小軸承運轉不靈活等均會引起縫線起絲和斷線（圖9）。
挑線鉤的安裝調整不當也會引起縫線起絲和斷線。挑線鉤的標準時間相位是：下勾線盤鉤頭勾住機針線環時，挑線鉤應挑出夾線器中間的縫線（圖10），如不正確，調整它的控制凸輪即可。另外還應注意挑線鉤的背面一定要光滑，否則縫線就不能進入挑線鉤內，夾線器中的縫線也就無法被挑出。另外，每次開始縫紉時縫線的長度不要超過90cm，超過了下線盤的容線量也會出現縫線起絲或斷線。
??? 機針掛紗
首先應檢查封針尖是否損壞或磨損，機針是否彎曲，封針位置是否正確。封針的標準位置是：當機針在上死點時，封針應封閉機針開口，封針尖距機針孔下端0.8~1.2 mm，封針尖與機針必須貼合。另外，夾線器松線時間過遲、線太緊也會造成機針變形掛紗。
??? 珠點調節手柄上下晃動
首先應檢查氣缸有無串氣現象（圖11），珠點正反按鈕、珠點調節按鈕有無接觸不良，檢查電磁閥動作是否靈活。如氣缸串氣沒有配件，應在氣缸橡膠圈槽內纏上兩三圈生料帶即可。如電磁閥線圈壞了只要換同樣型號的線圈。
??? 針碼和珠點故障
調節針碼和珠點大小時一定要先按下它們的調節按鈕，然后再調整，調好后再按回按鈕。如果不按按鈕直接調，不僅調不動，還會使調節絲杠滑絲，造成針碼和珠點無法控制；如果調好后忘了按回按鈕，針碼會亂，無法操作。珠點正反面大小不一致時，應旋松調節壓塊上的兩顆緊固螺釘反復調節（圖11）。
機針的停車位是靠同步器來定位的。機針的標準停車位是：在第二圈末端，機針下降至針板上面10 mm時應停車，此時上勾線鉤尾部距機針約10~14 mm。因珠邊機運轉兩圈完成一個工作循環，故調整同步器一定要認真觀察。調整不好，要么機針停在了第一圈末端，造成無法縫紉；要么停針位過高或過低，造成穿線時封針打不開或面料無法放入。同步器和主軸之間的皮帶張力要略緊。
781-type aircraft maintenance
Jump-edge machine needle is often the fault, jumping needle can be divided into: The hook-hook-line-and-jump-hook did not jump on the suture needle.
???? The hook-hook-line-dancing
How to determine the next hook-hook-line-dancing? ? In operation Shanggou line hook-Zhenxian Gouzhu Central, with a suture needle-drop, the next line hook-hook line, then slit the above material on the hook or cable lines, Central, this is because the next line hook-hook Gouzhu not the first machine needle on the Central Line caused by the needle jumped. Time-adjusted high degree of targeting criteria are: machine needles on the dead point in time to board plane needle tips from 16 mm. The hook-line time for the hook line: machine needles in the first lap down to the next point after death, upward rebound 1.3 mm, the hook-hook the first line should reach the concave center-pin (Figure 1), and the first hook - Needle concave gap is zero. Here want to emphasize is usually under-recovery of 1.3 mm, the hook-hook the first line should reach the centre of needles. This is because the needle-to-pin-drop when the needle was blocked in the closure of the side-board (2,3), the operator of the pinhole to the open side, the suture needle marks in the loss of protection, machine needles from the Died at a slight upward rebound of the suture needle marks Rally very easily lose a Central Line, if the hook-hook-line time slightly late in the Application List system on line before the suture needle marks, easily emerge from the plane or the Central Line Big jump-twisted cause. May also be under-hook-hook line slightly ahead of time.
????
???? Machine hook-line-dancing
Machine hook-line-dancing performance: sewing fabric in the front of a needle or a few needles without trace, or a few stitches after the machine-needle can not take on the suture. The failure to exclude, first of all machines should send the next line agencies understand, understand its working principles, time phase.
Machine needle in the first lap of death, when the rebound of 1.3 mm topical hook-hook-head Gouzhu Zhenxian Central, and will continue to expand the revolving line Central (4,5), followed by sutures will be sent into the line that → within the tight line hook in the line-in → folder. At the same time, the next line hook sent to the end of the previous trip, backward (the operator) Cazhe suture campaign to end after the trip, and then to suture Gouzhao campaign to stop before the trip ends. The second round of the machine without suture needle drop to the next point after the death began to rise, this time sending the suture line that pushed simultaneously around the left front of a machine needle movement, the delivery of that plane and meet at the needle The distance is 0.1 mm (Figure 4), rose to the closure of needle-shut-pinhole, sent under the line that started the Back, tight line hook-line, the line to open folder.
?????To ensure a smooth machine-stitching on the hook, then the next should be sent to each suture line hook, line refers to the next delivery, in-line folder, within the tight line hook. The important thing is to be sent each time the line hook Gouzhu suture, which requires them to be a good time for adjustment phase. Adjustment of the best observed using acupuncture board (the board the right-Modiao part), in order to observe the hook-line hook line, sending the hook-hook line and line delivery, the delivery of that line in delivery. The sending-line hook in the machine before the trip at the end of the standard position: the delivery line hook-and-distance is 2.5 mm. The delivery of the left hook in the standard position: under Gougou sent to the first line beyond the left-pin 0.3 mm. Rotary Matsushita sent on a fixed line hook screw adjusted (6). The line hook sent to the high-plate distance below 0.3 mm (Figure 7), Rotary Matsushita sent line hook fastening screws to regulate. Why should distance needle plate so close, mainly because of higher delivery line hook, line hook sent under the easier it is Cazhuo suture backward movement, will be able to return Gouzhu sutures. Machine-jump-hook line, the vast majority are due to the delivery line hook Gouzhu not caused by the sutures. The line hook sent to the back of the arc Cazhao suture backward movement, and then hook on the end of suture sent forward itinerary This is especially important. We must pay attention to the fact that, in the process of sewing Duanzhen, troubleshooting, best to check under the Arc hook sent to the back line there scratches, if sent to the back of a curved line hook Burr, then the present Hook sent back line movement, it is impossible to suture smoothly down the line hook sent under the front of the line hook will not send Gouzhu sutures, jump-it is very natural.
?? Folder line-adjusted properly, will lead to needle-line when the occasional jump hook needle. It is time to phase: the first lap under hook-line-Gouzhu Zhenxian Central rotating expand, tight line hook and line for folder on the left half of the next line hook-hook before the first around 8 mm, under the Application List system has begun to enter the line - . When the rebound in the second round of machine-Gouzhu suture needle was sealed shut after the pinhole, tight line hook-line, the line to open folder. Adjustment method is: Screw-line control cam folder on the two fastening screw adjustment (8), but should also be adjusted under the observation of the delivery line hook-time delivery phase is correct. This is because under the delivery line hook control cam and cam folder of control is linked to, if the delivery time line hook phase be affected, should be removed under the hook-line, the Line of Control in the folder Cam bed with wrench Screw-two fastening screws, which used the six-party wrench with a screw in the sliding bed, to change the delivery time line hook phase.
?
???? At the end of a long Xiantou
At the end of a long Xiantou ideal is about 10 cm, more than at the end of Xiantou on it that is too long, resulting in a waste of stitches. Xiantou long is the main reason for the adjustment of the delivery line hook improperly positioned under hook line and not transferred to the standard set position. In short to end Xiantou short, hook-line delivery of high not low, the hook-line hook-line time not later than early.
???? Suture spread, and disconnected from the wire
Silk sutures from the mainly due to the delivery of that line and sent folder line with the time-lines caused by premature. Adjustment method is to adjust their respective control cam time phase. Standard time phase in Figure 4, needle-point rise from the dead, sent under the simultaneous delivery of that line, closed-shut-pinhole, sent back to the beginning of that withdrawal, the folder open-line start-line. It also can adjust screw-line folder and change the size of the tension suture (5), the hook-line hook in the first stitches on the card if the head of the small hook or bearing operation does not lead to flexibility, all from the silk sutures And disconnected (9).
Pick the hook line will lead to improper installation of adjustment from the silk sutures and disconnected. Pick-hook phase is the standard time: The hook-line hook for the first Gouzhu Zhenxian Central, the pick-hook line folder should be singled out for the middle of the stitches (10), if not correct, adjust its control cam that is, Can be. It should also pay attention to the back of the pick-hook must be smooth, it will not be able to enter the pick suture line hook, line-folder in the suture it can not be singled out. In addition, each started sewing thread when the length of no more than 90 cm, set off the assembly line more than the capacity of line will also appear from the silk sutures or disconnected.
?
???? Machine-linked yarn
Should first check whether the closure needle damage or wear, whether bending machine needle, needle closure position is correct. The closure-standard position: When the machine needle in the dead spots, the closure of acupuncture needles should be closed openings, the closure of the needle marks from the bottom of 0.8 ~ 1.2 mm, with the closure of acupuncture needle to a paste. In addition, the folder line for late-line time, the lines too tight will cause deformation of needle pegged yarn.
???? - Point adjustment handle shaking from top to bottom
Should first check whether string gas in the cylinder (11), the positive and negative points-button, the button-point adjustment whether connection is bad, check whether the electromagnetic valve action flexible. If no gas cylinder string parts, rubber ring in the cylinder tank Chanshang February 3 laps to bring raw material. Such as electromagnetic coil valve bad for the same model as long as the coil.
?
???? Code-and-points of failure
Regulation needle-point code and the size must first press the button on their conditioning and then adjusted, for good and then click the back button. If the button is not directly transferred, not only for fixed, but also to adjust screw slippery silk, and a pin-point code can not control if good-by to forget after button, pin code will be chaotic, can not operate. - Point size is not negative, they should spin-conditioning Press tighten screws on the two repeatedly regulation (11).
Machine-parking spaces is to rely on sync with the positioning. Machine-standard parking spaces is: the end of the second lap, machine needles dropped to 10 mm above-board should be stopping, at this time Shanggou line hook from the tail-plane about 10 ~ 14 mm. By-side machines running two laps completed a work cycle, the adjustment synchronizer must seriously observe. Adjusted well, either machine needle stopped at the end of the first lap, causing no sewing; either stop-bit too high or too low, causing threading needles trying to open or closed when not Add to fabrics. And spindle synchronization between the belt tension Chamber tight.
8