購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
目 錄
前 言……………………………………………………………………………....1
1、珩齒加工的基本介………………………………………………............ ....... ….3
2、 運動設計……………………………….…………………………………….. ....13
2．1 給定條件……………………………….…………………………………….. ...13
2．2 確定結構式……………………………….………………………………….. .14
2．3 計算各級轉速……………………………….…………………………………15
2．4 電機選型……………………………….…………………………………….. ..15
2．5 擬定轉速圖……………………………….…………………………………….16
3、 確定各級傳動副齒輪的………………………………………………………….17
3.1確定齒輪的齒數........................................................................................ ...............17
3.2各軸及齒輪的計算轉速的確定……………………………………………………21
4、 傳動零件的初步計算................................................................ .............................26
4.1 傳動軸直徑初定......................................................................... ..........................26
4.2 主軸主要結構參數的確定....................................................................................27
4.3 齒輪模數計算和齒輪中心距的計算............................................................... .....28
4.4 軸的結構設計........................................................................................... ........... 29
4.5 皮帶的相關計算.................................................................... ..............................31
5、 主要零件的驗算............................................................................................ .......36
5.1 齒輪的強度驗算......................................................................... .........................36
5.2 主軸的驗算............................................................................................ ............ .39
5.3 花鍵的驗算............................................................................................ ............ .44
結束語........................................................................................................................46
致 謝……………………………………………………………………................48
參考文獻……………………………………………………………………................49
摘要
這篇畢業設計的論文主要闡述的是珩齒加工機床主軸箱的設計方法。珩齒加工機床是一種高精度加工機床.這個方法是以加工過程和珩齒加工機床的使用條件的數學和物理公式為基礎的。
在論文中，首先，對珩齒加工機床作了簡單的介紹，接著，闡述了主軸箱的設計原理和理論計算。然后按照設計準則和設計理論設計了主軸箱。接著對主軸箱的各部分組成進行了尺寸計算和校核。
目前，在珩齒加工機床的設計、制造及應用上，國內與國外先進水平相比仍有較大差距，國內在設計制造珩齒加工機床過程中存在著較多缺點。
關鍵字：珩齒加工，主軸箱，機床。
Abstract
This paper of graduation project mainly presents a systematic approach for the design of the headstock of plover machining tool, The plover machining tool is one of the members in the special high precision type machine family . the approach is based on the mathematical formulations and physical formulation on the generation process and conditions for the type of the plover machining tool.
In the paper , first of all , it is introduction about the plover machining tool .then , it is the principles about choose component parts of headstock. After that the headstock is designed abase on the principle. Then, it is checking computations about main component parts of headstock.
At present, we still fall far short of abroad advanced technology in design, manufacture and using. There are a lot of fault in the design of plover machining tool.
Key word: plover machining, headstock, machine.
注： 3