601 水平刮板輸送機

601 水平刮板輸送機,水平,輸送 英文原文Analysis and Precautions of Chain BreakageFailure of Scraper Conveyors1. ForewordScraper conveyor the fault, the failure to bound rupture the most prominent, and deal with the time spent by the labor intensity and also the largest. Maintenance often found that the chain of serious wear, the end of a chain of non-normal damage and a pit, and other phenomena. This paper analyses the reasons for the failure occurred, by preventive measures.2. analysisAccording to statistics, in the normal production of fully mechanized coal face, scraper conveyor chain conveyor failure time about the failure of more than 40 percent of the time. Ring linked bound rupture major fault caused by the following aspects(1) improper installation1) in the double-stranded different lengths. Under normal circumstances, single ≥ 200 kW power both in the use of double-stranded form, the new procurement scraper conveyor chain at the initial stage when there is no inconsistency in the length of the chain problem, because after the use of conveyor-bending level was advancing, through the chain A longer period of time after use,In the lateral (side-wall coal face) relative elongation of the chain, concentrated load, the heavy start-up occurred when bound rupture vulnerable. When the conveyor face again the next installation, assembly chain may be confusing, if short-chain installed in the lateral and medial in the long-chain equipment, conveyor work will result in biting sprocket chain, with a loose chain Sprocket was bitten and seriously so that when the chain pull off.2) chain link seam down. For the double-stranded conveyor at the time of installation in the Central Weld legislation must be progressive, to reduce wear Weld, extended chain link life; chain link Weld and reduce the friction and wear of the plate. However, in actual use, since the chain link wrong equipment, chain link seam down, and the frequent occurrence bound rupture fault.3) the use of short-scraper. As manufacturing quality problems or wear overrun by the use of the scraper, which, resulting in failure to stop production.4) rack deformation. Sprocket and rack itself allowed the rocky ledge of 5 mm, but the actual rocky ledge in excess of this value, sprocket and chain link connection is bad, a point contact, causing ring linked with the arc of Waterloo sprocket chain of non-normal wear and tear , A pit.5) nose to install high enough. When the nose to install high enough, the head drum Coal Unloader not due to the net, at the end of floating coal will be linked into the groove (that is, turn coal), an increase of the conveyor running resistance and increase the chain, the chute wear, So that the chain tension increased, bound rupture.(2) the use of improper maintenance1) sprocket transition wear. According to a point of order, ≥ 22 mm pitch of the biggest sprocket wear should be ≤ 6 mm (with the roundabout at sprocket chain-linked ring on the inspection and wheel above the distance), six months after the sprocket should use the nose, tail Sprocket to swap. However, in actual use, because of maintenance and use of cost considerations, the sprocket wear still in use, ring linked through the chain wheel when the slide because of the relative squeeze caused friction with the arc of the chain ring wear, and linked Waterloo Ring linked connection is bad, sprocket chain and ring pitch from the chain of non-aggravated the normal wear and tear.2) chain too tight or too loose. Tight at the beginning of the chain tension adjustment is too large, impact on conveyor normal work, shorten the chain of life, exacerbated by the board in the chain and wear, especially when the scratch card scraper, so that the chain elongation. When the chain-scraper, under the nose of a scraper sprocket chain piled up in the chain to interfere with, or even bite chain.3) and vertical degrees of bending gauge. Conveyor passage in the process, the level of the overrun is often due to face rugged, vertical degrees can not be fully guaranteed. Under such circumstances, the inevitable wear ring linked the increase of chain elongation increase.4) fault encountered at the engine frame. As the underground working conditions constantly changing, Shearer cut off layer, cut parting cases have occurred, then the waste water mixed with a cement-like, scraper, and the chain plate in the role of friction, wear the chain of intensified, More than normal wear and tear of coal condition, Sawtooth Central, Weld life cut short, the whole chain of life decline.5) Other damage. Electrical overload started, the running load will cause damage to link Central and bound rupture; began production in the face, cut in the bolt, metal scrap, etc. into the chute, resulting in biting card bound rupture; tight chain method is not correct , Will cause tension gauge and bound rupture(3) quality is not highCircle chain design load is about the broken scraper can withstand the tension about 10 times that in normal circumstances great safety factor, is not going to happen the bound rupture. However, due to various reasons, the ring chain (Sawtooth Central) less than the quality of standards, resulting in the production chain in the ring in bound rupture3 Ring linked Circle as a scraper conveyor chain of traction, its tensile strength directly related to the reliability of. At present, China's largest ring linked to φ42 mm × 146mm compact chain, tensile strength of 2270 kN, the largest foreign ring linked to φ48 mm × 152mm compact chain, tensile strength of 3550 kN. With the ring linked the increasing size of the central trough of higher and higher, conveyor magnificent performance declined, the gateway if not thorough clean-up will also affect passage of conveyor. So ring linked the direction of development is to improve tensile strength and reduce the high degree of Central legislation.3.1 Materials and Technology In order to improve the roundabout chain of tensile strength, the current foreign Grade C and D-linked ring in the large-sized materials with 23 MnNiCrMo54, 23MnNiCrMo54 and 23 MnNiCrMo64 scouring steel, tensile strength limit ≥ 1600 ~ 1800 MPa. Welding Technology: the use of advanced welding equipment, welding and the use of flash returns processing technology, successfully resolved the surfacing of the process of overheating, such as a burning issue. In quality testing, the use of scanning stretch fracture fracture of cables used to pre-tension ring linked to strengthen technology, greatly enhancing the carrying capacity and fatigue.3.2 form and geometry In 1985 the first to create a company 38 mm × 137mm flat chain. Flat is linked each of the chain is still ring-Central, Central was "squeezed" the flat ring. Flat chain link sliding work to reduce the size of the increase in the chain of slot pressure on the units and improve the legislation of the Central wear resistance; reduce its high level of the chain more easily through the sprocket, but can also reduce the capacity of power transmission and Bays of a high degree. Modern high-performance conveyor are generally involved in supporting a flat chain. Figure 5 conventional chain and a new wide-body linked flatIn 2003, the company has developed a wide-body at a flat linked, as shown in Figure 5. It is a high-intensity, low-chain, has the following characteristics:⑴ using this chain can reduce the high scraper chain, thereby reducing the central trough height, eventually reduce the use of high-mining, coal mining to meet thin. ⑵ using this chain can reduce the use of power, or power in the same circumstances, increase the length of face, it will greatly reduce the workload of opening up, reducing the number of face move.⑶ this forging of wide-body flat link chain has increased the contact area, can improve the chain link at the same time reduce the intensity of the wear and helps to maintain the rigidity of chain link. Such as a flat 42 mm chain can take 2 × 855kW of installed power, and 50 mm wide-body flat can be linked up to 3 × 1000kW bear the installed power.3.3 intelligent conveyor chain As unable to accurately predict the failure of the chain, according to conventional practices are generally ahead of the replacement of the chain. In 2005 a company with a number of research institutes to study the development of a conveyor chain-detection system, as shown in Figure 6. This is a combination of integrated sensor technology of intelligent conveyor chain, it will stress the chain of real-time record, the help of micro-electronics technology devices, from computers that the chain of life remaining before the fracture. It also can detect the preloads of the chain, is conducive to life during the period in the chain to achieve the best use of state, improve safety and avoid accidents.4. bound rupture fault approach(1) off on the single-chain: a single chain on bound rupture, the first clean pile of coal on the conveyor, reversing open space will be open to the bound rupture near the tail, and then use the brake, linked resistance (or monomer Pillar), and other tools so that the chain has some margin, with links connecting the ring will be broken;(2) off the double-stranded: in the double-stranded bound rupture, the first clean conveyor on the heap of coal, materials, winch wire rope leash on the lower part of the first chain to pull the tail direction, with open space will be reversed to open the bound rupture Near the tail, and then use the brake, linked resistance (or single prop), and other tools so that the chain has some margin, with links connecting the ring will be broken, or prepared the same length of the chain will bound rupture replaced;(3) off the double-stranded: in the double-stranded bound rupture, the first clean conveyor on the heap of coal, from the estimated bound rupture open multiple skylights to find bound rupture position; materials Road winch wire rope from the tail of the first lower plate Nose to the direction of penetration, with skylights, has been sent to wire rope bound rupture, leash on the lower part of the first chain to pull the tail direction, with open space vehicles will be bound rupture Department is open to the vicinity of the tail,Recycling-oriented chain pulley will be led by the head to the tail of the board above the trough of the transition; reuse winch wire rope will lead to decapitation above the tail, and then use the brake, linked resistance (or single prop), and other tools so that the chain Have a certain margin, with links connecting the ring will be broken, or prepared the same length of the chain will bound rupture replacement.5. bound rupture fault preventive measures(1) strictly control the quality of the installation1) installation, they should point-components, according to the order to install loading transport, to prevent the components were insufficient to replace the old;2) all eyes on the face plate processing (in particular, will be cleared of scrap metal) to determine the nose, tail position, while the installation of the nose should be set aside or highly processed to meet the mounting height to prevent the installation of the wrong location Need to co-opt parts, or for unloading high enough damage to the chain;3) require the installation of the equipment, fastening bolts scraper, with the anti-chain, the scraper must be reworked;4) The installation process is prohibited frequent point vehicles, to avoid components, parts damaged.(2) to enhance equipment maintenance and management1) equipment in the operation to eliminate the use of unqualified chain link ring;2) the strict requirements of pushing wandering step over and over bending; Shearer asked the driver to control roof and floor to prevent a floor-level, to prevent conveyor overload;3) when the chain tight to prevent the chain too tight or too loose;4) the use of the old chain, such as the length of the chain should be tied up in pairs to use, if unable to find the same length of chain, the long chain can be disconnected from the two bundled into use, ranging from the length of the chain mix is prohibited, prohibited the use of breaking strength Not enough chain;5) of the periodic maintenance sentinel system, as required periodic replacement of the tail sprocket nose, to reduce the wear chain and sprocket.(3) improve the quality of technical workers, according to many years of experience, who after training in the installation of the work of the staff, efficient and reworked the low rate, the conveyor failure rate is also low. Therefore only strengthen training and improve the quality of technical workers, in order to prevent the occurrence of an abnormal failure to reduce the incidence of insecurity and improve the economic benefits of coal mine production.中文譯文 刮板輸送機斷鏈故障分析及防范措施1. 前言刮板輸送機出現的故障中,以斷鏈故障最為突出,處理時所花費的時間及勞動強度也最大。檢修經常會發現鏈條嚴重磨損、鏈條外端部有非正常損壞并出現凹坑等現象。本文分析故障發生的原因,提出防范措施。2.　分析據統計,在正常生產的綜采工作面,刮板輸送機鏈條故障時間約占輸送機總故障時間的40%以上。圓環鏈斷鏈故障主要由以下幾個方面引起:(1) 安裝不當1) 中雙鏈長短不一。一般情況下,單機功率≥200kW時均采用中雙鏈形式,新采購的刮板輸送機鏈條在初期使用時不存在鏈條長短不一致的問題,使用后由于輸送機呈臺階形彎曲推進,鏈條經過較長一段時間的使用后,處于外側(工作面煤壁側)的鏈條相對伸長,集中載荷,在重載起動時極易發生斷鏈。當該輸送機在下一個工作面再次安裝使用時,鏈條可能混亂裝配,如果短鏈裝在外側,長鏈裝在內側,輸送機工作時將造成外鏈過緊咬鏈輪、內鏈過松被鏈輪咬,嚴重時使鏈條拉斷。2) 鏈環焊縫向下。對于中雙鏈輸送機在安裝時立環焊縫必須向上,以減少焊縫磨損,延長鏈環壽命;并可減少鏈環焊縫對中板的摩擦磨損。但在實際使用中,由于鏈環錯裝,鏈環焊縫向下,而發生頻繁斷鏈故障。3) 使用短刮板。由于制造質量問題或因使用磨損超限的刮板,致使,造成故障而停止生產。4) 機架變形。鏈輪與機架本身允許有5mm的竄動量,但當實際竄動量超過此值,鏈輪與鏈環接觸不良,出現點接觸,造成圓環鏈圓弧段與鏈輪鏈窩的非正常磨損,出現凹坑。5) 機頭安裝高度不夠。當機頭安裝高度不夠時,機頭滾筒由于卸煤不凈,底鏈將浮煤拉入下槽(即回頭煤) ,增加了輸送機的運行阻力,增大了鏈條、溜槽的磨損量,使鏈條張力增大,斷鏈。(2) 使用維護不當1) 鏈輪過渡磨損。根據規程,節距≥22mm的鏈輪最大磨損量應≤6mm (用圓環鏈平置于鏈輪上檢查圓環鏈上面與輪轂的距離) ,鏈輪使用半年后應將機頭、機尾鏈輪進行調換。但在實際使用中,由于考慮維修和使用成本、磨損嚴重的鏈輪仍在使用,圓環鏈在通過鏈輪時由于相對滑動摩擦與擠壓而造成圓環鏈圓弧段磨損,鏈窩與圓環鏈接觸不良、鏈輪與圓環鏈節距不等加劇了鏈條的非正常磨損。2) 鏈子過緊或過松。在緊鏈時初張力調整過大,影響輸送機正常工作,縮短了鏈條的使用壽命,加劇了鏈條與中板的磨損量,特別是當刮板被刮卡時,使外鏈伸長。當刮板鏈過松時,在機頭鏈輪下造成刮板鏈條堆積,發生與鏈條干涉,甚至啃咬鏈條。3) 彎曲度和垂直度超限。輸送機在推移過程中,水平度超限是經常發生的; 由于工作面凹凸不平,垂直度也不能完全保證。在這種情況下,圓環鏈必然磨損增大,外鏈伸長加大。4) 遇到斷層時拉矸石。由于井下工作條件的不斷變化,采煤機割斷層、割夾矸情況時有發生,此時的矸石與水相混合形成水泥狀,在刮板、鏈條與中板摩擦作用下,鏈條磨損加劇,磨損量超過正常運煤工況,鋸齒環、焊縫壽命減短,鏈條整體壽命下降。5) 其它損壞。電機過負荷啟動、過負荷運行將造成鏈接環損壞而斷鏈;在工作面開始生產時,切眼內的錨桿、金屬廢料等拉入溜槽,造成蹩卡而斷鏈;緊鏈方法不正確,也會造成張緊力超限而斷鏈。(3) 質量不高圓環鏈設計的破斷載荷約為刮板可承受拉力的10倍左右,在正常情況下安全系數很大,是不會發生斷鏈的。但由于種種原因,圓環鏈(鋸齒環)的質量達不到標準,致使在生產中圓環鏈發生斷鏈。3 圓環鏈圓環鏈作為刮板輸送機的牽引機構，其抗拉強度直接關系到整機的可靠性。目前，國產圓環鏈最大到 φ42mm×146mm 緊湊鏈，抗拉強度為2270kN，國外圓環鏈最大到 φ48mm×152mm 緊湊鏈，抗拉強度為3550kN。隨著圓環鏈尺寸的不斷增大，中部槽也越來越高，輸送機壯美效果隨之下降，回采巷道如果清理不徹底還會影響推移輸送機。所以圓環鏈的發展方向是提高抗拉強度和降低立環高度。3.1 材料及工藝為了提高圓環鏈的抗拉強度，目前國外 C 級和 D 級大規格圓環鏈在材料方面用 23MnNiCrMo54，23MnNiCrMo54 和 23MnNiCrMo64 精練鋼，拉伸強度極限 ≥1600～1800MPa。焊接工藝方面：采用先進的堆焊設備，b?采用閃光堆焊和退貨加工工藝，成功地解決了堆焊過程中產生的過熱、過燒等問題。在質量檢測方面，對啦伸斷口利用掃描電纜進行斷口分析；采用圓環鏈預拉伸強化工藝，極大提高了承載能力和疲勞強度。3.2 形式與幾何尺寸1985 年某公司率先制造出 38mm×137mm 扁平鏈。扁平鏈就是每根鏈條的平環仍然是圓環，而立環是被“擠壓”的扁平環。扁平鏈鏈環滑動工作面積的增大降低了鏈條在槽體上的單位壓力，提高了立環的抗磨損性能；鏈條高度的降低使其更容易通過鏈輪，而且可以降低裝機功率和輸送機槽體高度?，F(xiàn)代高性能輸送機一般都涉及配套扁平鏈條。2003 年，某公司有研制處一種寬體扁平鏈，如圖 5 所示。它是一種高強度、低矮型鏈條，具有以下特點：圖 5 常規鏈條和新型寬體扁平鏈⑴采用這種鏈條可降低刮板鏈高度，從而降低中部槽高度，最終使用采高降低，滿足薄煤層開采。⑵采用這種鏈條可以降低使用功率，或在功率不變的情況下，增大工作面的長度，這將極大地減少開拓工作量，減少工作面搬家次數。⑶這種鍛造的寬體扁平鏈加大了鏈環的接觸面積，可在提高鏈環強度的同時減少磨損，有助于保持鏈環的剛性。如 42mm 的扁平鏈可以承受 2×855kW 的裝機功率，而 50mm 寬體扁平鏈則可承受高達 3×1000kW的裝機功率。3.3 智能輸送機鏈由于無法準確地預測鏈條的失效，按常規做法一般都是提早更換鏈條。2005 年某公司與多家科研院所合作，研究開發一種輸送機鏈在線檢測系統。這是一種融合了集成傳感器技術的智能輸送機鏈，它能將鏈條的應力特性實時記錄下來，借助微電子技術裝置，由計算機得出鏈條斷裂前的剩余使用壽命。另外還可以檢測鏈條的預緊力，有利于鏈條在使用壽命期內達到到最佳使用狀態，提高安全性，避免意外事故。4　斷鏈故障處理方法(1) 斷上單鏈:發生上鏈單根斷鏈時,首先清掉輸送機上堆煤,開空倒車將斷鏈處開到機尾附近,然后利用剎車器、阻鏈器(或單體支柱)等工具使鏈條有一定的裕量,用鏈接環將斷處連接;(2) 斷上雙鏈:發生上雙鏈斷鏈時,首先清掉輸送機上堆煤,用材料道絞車鋼絲繩拴住下部鏈頭向機尾方向拉動,配合開空倒車將斷鏈處開到機尾附近,然后利用剎車器、阻鏈器(或單體支柱)等工具使鏈條有一定的裕量,用鏈接環將斷處連接,或用準備好的相等長度的鏈條將斷鏈更換;(3) 斷下雙鏈:發生下雙鏈斷鏈時,首先清掉輸送機上堆煤,從估計斷鏈處打開多個天窗尋找斷鏈位置;用材料道絞車鋼絲繩頭從機尾中板下部向機頭方向穿入,借助天窗,將繩頭一直送到斷鏈處,拴住下部鏈頭向機尾方向拉動;配合開空正車將斷鏈處開到機尾附近,再用導向滑輪將鏈頭牽到機尾中板上面過渡槽以下;再用絞車?yán)K頭將上面斷頭牽到機尾,然后利用剎車器、阻鏈器(或單體支柱)等工具使鏈條有一定的裕量,用鏈接環將斷處連接,或用準備好的相等長度的鏈條將斷鏈更換。5　斷鏈故障防范措施(1) 嚴格控制安裝質量1) 安裝時,應點清元件數量,按安裝順序裝車運輸,以防止元件不足時用舊件替代;2) 對工作面切眼底板進行整理(特別是將廢舊金屬物清理干凈) ,確定機頭、機尾位置,同時應預留機頭的安裝高度或進行處理以滿足安裝高度,防止安裝位置錯誤需要增補部件,或因卸載高度不夠損壞鏈條;3) 按設備要求進行安裝,緊固刮板螺栓,對裝反的鏈條、刮板必須返工;4) 安裝過程中嚴禁頻繁點車,避免元件、部件損壞。(2) 加強設備的維護管理1) 在設備運行中,杜絕使用不合格的鏈條、鏈接環;2) 要求推溜工嚴格推移步距和推移彎曲度;要求采煤機司機控制好頂?shù)装?以防出現臺階形底板,嚴防輸送機過負荷工作;3) 緊鏈時防止鏈條過松或過緊;4) 使用舊鏈條時,須將等長度的鏈條成對捆綁使用,如果無法找到同長度鏈條時,可將長鏈從中斷開成兩節捆綁使用,嚴禁不等長度鏈條混用,嚴禁使用破斷強度不夠的鏈條;5) 實行定期定點檢修制,按要求定期更換機頭機尾鏈輪,以減少鏈輪和鏈條的磨損。(3) 提高職工技術素質,據多年來的使用經驗,凡經過培訓后從事安裝工作的員工,工作效率高,返工率低,輸送機故障率也低。因此只有加強培訓,提高職工的技術素質,才能防止不正常故障的發生,減少不安全因素的發生,提高煤礦生產的經濟效益。