普通機床改造成鍵槽銑床

普通機床改造成鍵槽銑床,普通,機床,造成,鍵槽,銑床 目 錄 0.引言 ……………………………………………………………………1 1.總體方案論證 …………………………………………………………………3 §1.1機床的初步設計 …………………………………………………3 §1.2機床工藝方案的擬定 ……………………………………………3 §1.3機床運動方案的擬定 ……………………………………………3 §1.4機床技術參數的確定 ……………………………………………4 §1.5機床總體布局的確定 ……………………………………………4 §1.6機床原理圖的擬定 ………………………………………………5 §1.7機床總體尺寸聯系圖的繪制 ………………………………………5 §1.8其他 ………………………………………………………………5 2.計算部分 ………………………………………………………………6 §2.1銑刀銑削功率的確定 ……………………………………………6 §2.2電機的選擇 ………………………………………………………7 §2.3減速機的選擇 ……………………………………………………7 §2.4V帶的選擇 …………………………………………………………12 §2.5主軸剛度強度校核 ………………………………………………15 3.設計部分 ………………………………………………………………15 §3.1蝸輪傳動部分 ……………………………………………………15 §3.2帶傳動部分 ………………………………………………………16 §3.3銑刀的選用 ………………………………………………………17 §3.4軸的選擇 …………………………………………………………17 §3.5箱體的設計………………………………………………………19 4.結論 ……………………………………………………………………21 工作小結 …………………………………………………………………22 致謝 ………………………………………………………………………23 參考文獻 …………………………………………………………………24 附件清單 ……………………………………………………… 25 摘要 本文作者研究了普通機床改造成鍵槽銑床時銑頭立柱部件的改進方案。利用廢舊機床的床身、床架、床鞍等基架部件進行改造設計，不僅節約了機床維護費用，同時提高了機床的回收利用率，是企業廢舊機床未來利用的發展趨勢。新的銑床立柱部件采用了電機、減速機、帶輪的傳動系統，使的銑刀的轉速保持在一定的范圍之內，減少了刀具振動引起的工件精度偏差。加入了升降螺桿裝置和轉輪，使得刀具在縱向的進給量可進行手工調節，提高了加工精度。皮帶輪處采用簡易張緊裝置，可及時的對帶輪的松脫，打滑現象進行調整，保證了傳動的連續性。經過各種方案的比較，得出上述設計確是切實可行的，提高了機床的回收率，增加了機床的加工范圍。 關鍵詞：銑床 銑頭立柱部件 升降螺桿 Summary Author of this text study ordinary lathe transform keyway mill head post improvement scheme of part on the milling machine. Utilize old and useless lathe bed, bedstead of lathe, bed saddle, etc. base shelf part carry on transformation design, Economize lathe maintain the expenses, improve the recovery utilization ratio of the lathe at the same time not merely, It is the development trend that enterprises utilize in old and useless lathe future. The new post part of milling machine has adopted electrical machinery, moderating machine, transmission with wheel, Rotational speed of milling cutter that make keep and within certain range, reduce cutter work piece precision deviation that vibration cause. Put into hoist or lower spiral shell pole device and runner , make cutter entering giving amount can be regulated by hand vertical, Have improved the machining accuracy . Belt pulley office adopt simple and easy pieces of urgent device, can to lead wheel loose to take off, Skid phenomenon adjust, guarantee the continuity of the transmission. Through various kinds of comparison of scheme, draw and design not really feasible while being above- mentioned, Have improved the rate of recovery of the lathe , has increased the processing range of the lathe . Keyword: The milling machine mills the post part of head Hoist or lower spiral shell's pole