沖壓式芡實剝殼機

沖壓式芡實剝殼機,沖壓,芡實,剝殼 沖壓式芡實剝殼機 目錄 沖壓式芡實剝殼機.....................................................................................................................3 摘要.............................................................................................................................................3 ABSTRACT...............................................................................................................................4 THE HEAD METAL CLIPPER DESIGN.............................................................................4 1 緒論..........................................................................................................................................5 1.1 課題選擇的背景和目的 ...................................................................................................5 1.2 沖壓式芡實剝殼機國內外發展現狀 ..............................................................................6 1.3 沖壓式芡實剝殼機的現狀 ..............................................................................................7 1.3.1 沖壓式芡實剝殼機在車間布置和作用 ..................................................................................7 1.3.2 沖壓式芡實剝殼機的類型和特點....................................................................................7 1.3.3 沖壓式芡實剝殼機研究的內容和方法 ..................................................................................8 2 方案的選擇與評述...............................................................................................................10 2.1 方案選擇 .........................................................................................................................10 2.2 方案評述 .........................................................................................................................10 3 電機的選擇...........................................................................................................................12 3.1 剪切力的計算 .................................................................................................................12 3.2 剪切機的扭矩計算 .........................................................................................................12 3.3 剪切時,轉股穩定運轉轉速 .......................................................................................13Hn 3.4 電機型式及電機容量的選擇 .........................................................................................13 4 主要零件的強度計算.........................................................................................................16 4.1 減速機的計算 .................................................................................................................16 4.1.1 減速機的傳動比分配..................................................................................................................16 4.1.2 減速機齒輪設計 ...........................................................................................................................16 4.1.3 齒輪軸的設計計算 ......................................................................................................................24 4.2 剝殼的設計 .....................................................................................................................29 4.2.1 材料的選擇 .....................................................................................................................................29 4.2.2 剝殼的結構設計 ...........................................................................................................................29 4.3 轉股軸承的選擇及校核 .................................................................................................30 4.4 側隙調整機構的設計 .....................................................................................................31 4.5 電動機的起動力矩的驗算 .............................................................................................32 4.5.1 系統飛輪力矩的計算..................................................................................................................32 4.5.2 起動時間的計算 ...........................................................................................................................33 4.5.3 起動轉角的校核 ...........................................................................................................................33 5 潤滑方法的選擇...................................................................................................................37 5.1 減速機潤滑方法及潤滑油的選擇 .................................................................................37 5.2 沖壓式芡實剝殼機的潤滑 .............................................................................................37 6 試車方法和對控制的要求....................................................................................................38 6.1 試車要求 .........................................................................................................................38 6.2 對控制系統的要求 .........................................................................................................38 7 設備可靠性與經濟評價........................................................................................................39 7.1 機械設備的有效度 .........................................................................................................39 7.2 投資回收期 .....................................................................................................................39 專題-電動機選擇與探討 .........................................................................................................41 1.三相異步電動機的旋轉原理 : .........................................................................................42 2.同步電動機在結構上大致有兩種：....................................................................................43 3.電機固有步距角：................................................................................................................44 4.步進電機的一些特點：........................................................................................................45 5.電動機的潤滑 ....................................................................................................................46 結論...........................................................................................................................................47 致謝...........................................................................................................................................48 參考文獻...................................................................................................................................49 附錄-外文翻譯 .........................................................................................................................50 MODELING AND OPTIMIZATION FOR A 20-H COLD ROLLING MILL...............................................50 1、FORCE ,TORQUE AND POWER ................................................................................................51 2、MATERIAL YIELD STRESS ADAPTION ....................................................................................52 3、FRICTION REPRESENTATION .................................................................................................52 4、ELASTIC MILL STAND BEHAVIOR ..........................................................................................53 5、SUMMARY ............................................................................................................................54 建模與優化為 20 - H 的冷連軋 ...............................................................................................55