裝配圖低位放頂煤液壓支架的設計(1)
裝配圖低位放頂煤液壓支架的設計(1),裝配,低位,放頂煤,液壓,支架,設計
xx大學
畢業設計
姓 名： 學 號：
學 院：
專 業：
論文題目： 低位放頂煤液壓支架的設計
指導教師： 職 稱：
20 年 月
畢業設計任務書
學 院 機械與動力工程學院
專業年級
學生姓名
任務下達日期： 20 年 月 日
設計日期： 20 年 月 日至 20 年 月 日
設計題目：低位放頂煤液壓支架設計
設計專題題目：低位放頂煤液壓支架頂梁及立柱
設計主要內容和要求：
1. 設計要求：
完成液壓支架總體方案確定及設計
主要零部件設計
完成設計圖紙（折合0＃）3張
2. 主要工作參數：
頂板條件：老頂 Ⅲ級
直接頂 2類
底板比壓: 1.5MPa
工作阻力： 4000kN
推溜力： 150KN
拉架力： 300KN
泵站壓力：32MPa
適應煤層傾角：<150
院長簽字： 指導教師簽字：
大學畢業設計指導教師評閱書
指導教師評語（①基礎理論及基本技能的掌握；②獨立解決實際問題的能力；③研究內容的理論依據和技術方法；④取得的主要成果及創新點；⑤工作態度及工作量；⑥總體評價及建議成績；⑦存在問題；⑧是否同意答辯等）：
成績： 指導教師簽字：
年 月 日
畢業設計評閱教師評閱書
評閱教師評語（①選題的意義；②基礎理論及基本技能的掌握；③綜合運用所學知識解決實際問題的能力；③工作量的大??；④取得的主要成果及創新點；⑤寫作的規范程度；⑥總體評價及建議成績；⑦存在問題；⑧是否同意答辯等）：
成績： 評閱教師簽字：
年 月 日
畢業設計答辯及綜合成績
答 辯 情 況
提 出 問 題
回答問題
正確
基本正確
有一般性錯誤
有原則性錯誤
沒有
回答
答辯委員會評語及建議成績
答辯委員會主任簽字：
年 月 日
學院領導小組綜合評定成績
學院領導小組負責人：
年 月 日
畢業設計（論文）開題報告
題目名稱
低位放頂煤液壓支架的設計
姓名
專業班級
學號
一、 選題的目的和意義
隨著工業技術的不斷發展，國民經濟對煤炭需要量的日益增加，煤礦開采，特別是采煤工作免得生產技術面貌發生了巨大的變化。自1954年英國裝備了世界上第一個液壓支架工作滿開始，采煤技術實現了綜合機械化。綜合機械化采煤，就是工作面采煤，運輸和支護三大主要生產環節都實現機械化。也就是說，采用滾筒式或刨削式等采煤機械落煤與裝煤；工作面重型可彎曲運輸機，以及與之適應的順槽轉載機和可伸縮皮帶運輸機等運煤；自移
式液壓支架支護和管理頂板。這幾種設備相互配合，組成了綜合機械化采煤設備。
液壓支架是以高壓液體為動力，由若干液壓元件（油缸和滑件）與一些金屬結構件組合而成的一種支撐和控制頂板的采煤工作面設備，能實現支撐，降落移架和推移運輸機等一整套工序。液壓支架技術上先進，經濟上合理，安全上可靠，當前世界各國都在不斷地提高采煤工作面的綜合機械化水平。
二、 國內外研究綜述
我國目前液壓支架與發達國家的差距：
1.生成能力上的差距 我國目前大部分支架的可靠性與國外差距比較大。進口支架工作面開機率達到90%以上，日產達到了30000t，年產達到10Mt，支架大修周期為產煤15Mt以上。而我國目前綜采工作面開機率平均為50%左右。支架大修周期為產煤量在4～5Mt左右。
2.支護性能參數的差距 發達國家在設計指導思想方面大多主張大馬拉小車，支架的工作阻力與支護強度普遍較大。工作阻力一般都在7000KN以上，最高達到10000KN，而我國目前支架的工作阻力與國外相比普遍偏低，平均在4000～5000KN，相差30%左右。
另外，國外支架中心距普遍采用1.75m，個別達到2m，我國支架中心距絕大多數為1.5m。
3. 結構件材料的差距 目前國外σs＝700～800MPa的鋼材以廣泛應用，而我國普遍使用的是σs＝450MPa以下的鋼板，相差30%～40%。
4.控制系統方面的差距 目前世界上一些發達國家支架的控制系統已廣泛采用電液控制系統，而我國目前很少采用電液控制，絕大部分為手動。
液壓支架的發展趨勢：
1.提高支架的可靠性，另外加大支架的中心距也是必然趨勢；
2.二柱支架將是主導架型，目前我國的四柱支架要比二支柱支架數量多，相比較而言二柱支架具有明顯的優勢；
3.采用大采高支架；
4.電液控制系統是液壓支架發展的方向；
5．放頂煤支架將是未來的主導架型；
三、畢業設計（論文）所用的方法
本次設計，是本人按照導師的要求，結合自己的興趣愛好，通過收集大量的理論資料，參加生產實習的基礎上，自主完成的畢業設計。其中，在設計過程中頂梁和立柱是設計的重點。另外，本論文還著重介紹了液壓支架的結構，類型，工作原理，特點，液壓支架的維護和管理，及其常見的故障及排除方法。目的是通過對支掩式液壓支架進行深入細致的了解和研究，在一定的理論基礎上，結合實踐認識，鞏固所學知識，完成自主實踐與創新。
在設計過程中遇到的問題我們一般通過自己查閱資料和小組討論的方式解決，如確實有不能解決的問題我們就通過請教廠方技術人員和指導老師，爭取解決在畢業設計過程中所有問題。
四、主要參考文獻與資料獲得情況
參考文獻：
1. 主編《機械設計手冊》第三版 化學工業出版社1999．
2. 武同振 趙宏珠 吳國華主編《綜采綜掘高檔普采設備選型配套圖集》中國礦大出版社1993
3. 楊振復 羅恩波 主編《放頂煤開采技術與放頂煤液壓支架》煤炭工業出版社1995
4. 丁紹南編著《采煤工作面液壓支架設計》世界圖書出版社1992
5. 劉鴻文 主編《材料力學》第三版（上、下）高等教育出版社1992
6. 邢?？? 蔡坫 劉玉堂主編《煤礦支護手冊》煤碳工業出版社1993
五、畢業設計（論文）進度安排（按周說明）
1. 5-6周 畢業實習
2. 6周 定出設計方案
3. 7-9周 設計總體方案設計裝配圖
4. 10-12周 零構件設計
5. 13-14周 畢業設計說明書
六. 指導教師審批意見
指導教師： （簽名）
年 月 日
畢業設計論文 支撐掩護式液壓支架 中文摘要 現代煤礦高效工作面的關鍵設備液壓支架 ,是煤礦實現采煤、運輸和支護等所有工序 全部機械化的重要環節。 支撐掩護式支架是以支撐為主 ,掩護為輔的液壓支架 ,用來控制采場頂板下沉斷裂及 冒落 ,保證控頂距內頂板完整和必要的回采空間。對支撐掩護式液壓支架的結構特點及合 理應用等進行了簡要介紹。為保證支架的合理工作狀態 ,應盡量縮短降架時間 ,快速移架 ,及 時支護 ,并保持足夠的支架初撐力在詳細分析液壓支架初撐力與直接頂相互作用機理的基 礎上,對支架合理初撐力的確定進行了分析研究,并提出了合理支架初撐力的確定方法。 關鍵詞：液壓支架 支護 初撐力 畢業設計論文 ABSTRACT Hydraulic Support he hydraulic support is the key equipment in today's high production faces underground,it is important Standing shield hydraulic support can control the subsidence,rupture and inbreak of the stope roof,and assure the integrity of the roof and necessary extraction space.The structural feature and its rational application of standing shield hydraulic are introduced in brief.According to the paper,it is necessary to reduce the time of falling support,to move support quickly,to timber the roof in time and keep enough setting pressure. On the basis of analysis of the reciprocity mechanism of original pressure and direct roof, the author analyzes the setting methods of appropriate original pressure of powered support is put forward finally. Keywords: hydraulic support shoring put forward finally 液壓支架分級分布式微機電磁閥液壓控制系統
摘 要 以集散型控制理論為基礎，論述了綜采工作面液壓支架分級分布式微機電液控制系統的原理，給出了液壓支架的3種控制模型，設計了以MCS-51單片機為核心的液壓支架控制器，進行了控制器的硬件設計和軟件調試。
關鍵詞 集散型控制系統；液壓支架；單片機
中圖分類號 TP273；TD355.4
A Distributed Computer Control System
of Mining Hydraulic Support
Ma Chunyan Li Gengxin Yang Jiankang
(College of Information Engineering of TUT)(Jin Cheng Mining Bureau)
Abstract This paper presents the principles of distributed computer control system of mining hydraulic support for the coalface with complex cutting equipment on the basis of the distributed computer control theory.Three control modes of the hydraulic support are supplied in the paper.It also deals with the design of the hydraulic support controller with the pricipal part of a MCS-51 single chip computer.In addition,the hardware circuits design and software program adjustment of the controller are also mentioned in the paper.
Key words distributed computer control system;hydraulic support;
single chip microcomputer
采煤工作面綜合機械化設備CCME(Coalface Complex Mechanical Equipements),主要由采煤機、液壓支架和刮板運輸機(俗稱煤溜子)等設備組成。液壓支架是綜合機械化采煤工作面的主要設備之一，它分散布置在整個采煤工作面上。一個工作面一般裝備100架左右或更多的液壓支架。為了有效地提高綜采工作面的生產效率和管理水平，本文以集散型控制系統DCCS(Distributed Computer Control Systems)理論為基礎，設計了液壓支架分級分布式微機電液控制系統。
中文摘要
?
課題根據當前綜合機械化采煤工作面所采用支護方式暴露出來的問題，提出采用自移式超前支護液壓支架對綜放面端頭進行超前支護；考慮到現今液壓支架生產企業在產品開發過程中存在的種種弊端，提出將虛擬樣機技術應用到液壓支架的設計開發中。在支架投入生產之前在計算機上仿真和修改數字樣機，縮短了研發周期，提高了產品質量，減少了由于制造物理樣機而增加的成本。本課題也為其他機械產品的開發提供了一個成功的范例。課題介紹了虛擬樣機技術、國內外液壓支架的發展?fàn)顩r以及利用虛擬樣機技術進行自移式超前支架開發的意義；介紹了自移式超前支架的結構特點、承載原理以及應用MALTAB語言編寫M文件的方式自動計算出自移式超前支架的主要技術參數；介紹了自移式超前支架液壓控制系統的特點和常用的液壓基本回路，設計出自移式超前支架的液壓控制系統，提出基于虛擬樣機技術的液壓控制系統的實現方法。在UG-NX環境下完成了自移式超前支架零部件的三維造型設計并采用自底向上的裝配方式，完成了支架的虛擬裝配，查找設計不合理的因素，計算出自移式超前支架的質量、體積、轉動慣量等物理特性，并且完成了從3D實體模型圖到2D工程圖的生成。將零部件的3D模型按照Parasolid標準輸出“.x_t”文件，為ANSYS進行有限元分析做準備。介紹了有限元法的基本原理及其求解步驟，在研究CAE技術和CAD技術之間的數據傳輸?shù)幕A(chǔ)上，提出利用ANSYS和UG-NX的數據接口，將UG-NX環境下輸出的“.x_t”文件導入ANSYS環境下，進行網格劃分、約束加載求解、后處理，完成自移式超前支架主要承載部件（如頂梁等）的應變、應力分析，根據零部件在承載狀態下變形量的大小驗證零部件的設計是否合理。
?
外文摘要
?
The thesis raises designing the automatic advanced hydraulic bracket to support the terminal of the working fields according to the problems exposed to the supporting method nowadays being used in mechanized coal cutting. Considering the hydraulic bracket company has many maladies during the development of the products, The thesis raises adopting Virtual Prototyping to design the product. By simulation and modifying digital prototyping on computer before product, we can reduce the costs and shorten the design interval and improve the quality of the products. The theme also provides a successful paradigm for the design of other machinery products. The thesis introduces Virtual Prototyping technology, development of the hydraulic supports and the significance of designing automatic advanced bracket based on Virtual Prototyping technology. The thesis introduces the structure features of the bracket, the principle for enduring the load and instructs a method of counting key technology parameters using MATLAB to edit M files. The features and the fundamental circuit of the hydraulic controlling system are also instructed, and the hydraulic controlling system of the automatic advanced bracket is designed, putting forward the method of emulating based on the Virtual Prototyping technology. The thesis achieves three dimension design for the parts of the bracket, and completes virtual assemble using Bottom-Up assembly, checking irrational factors in the design, counting the quality, volume and the retary inertia of the assembly solid and creating engineering drawing from 3D model to 2D view in UG-NX. “.x_t” files of the 3D models are exported by Parasolid standard and make ready for the analysis using ANSYS software. The thesis instructs the principle for the FEA and solving steps, put forward the method of guiding the “.x_t” file into ANSYS conditions based on the investigation of the interface between the CAE technology and CAD technology, making analysis of stress and strain for the main loading parts (ef. upper beam, etc) of the automatic advanced bracket by meshing, loading-solving and postprocessing, and verifying the result of the design of the parts in loading conditions according to the strain.
高強度結構鋼的焊接試驗及液壓支架有限元分析/THE WELDING EXPERIMENTS OF HIGH STRENGTH STRUCTURAL STEEL AND THE FINITE ELEMENT STRENHTH ANLYSIS OF FLUID POWER BEARER
中文摘要
?
本文對抗拉強度為800 高強鋼WH80的焊接性能進行了研究，實驗數據表明高強鋼WH80可以用于支架設計。初步總結了一套焊接工藝，包括預熱溫度的確定、低強度匹配的可行性、焊接速度的選取以及線能量的確定等，這些研究方法與手段可以直接用于生產實踐。對支架整架結構件裝配體進行了應力分析，建立了具體的分析模型，對于外載荷的處理、邊界條件的確定提出了具體的處理方法，建立了完整的支架簡化結構模型。通過研究，可以得出如下結論： (1) 高強鋼WH80屬于低焊接冷裂紋敏感性鋼，可用作支架設計板材。 (2) WH80鋼可以選用比母材強度低的焊接材料J707RH進行焊接，以使接頭強度與母材強度等強。 (3) 預熱溫度的確定除考慮材料化學成份外，還應考慮到晶向組織的變化。對于WH8O高強鋼為防止脆化，預熱溫度應選定在120 左右。 (4) 支架在頂梁偏載工況下受力狀況最為惡劣，表現為支架頂梁、斜梁、前后連桿和底座等處都有較大的應力分布。 (5) 最高Von Mises應力分布表現為區域性、局部性的存在，在實際設計中應考慮在該區域施以高強度板材，而無需整架采用高強度板材，以節省支架成本。
?
外文摘要
?
This topic research content was 800 high tensile steel WH80 welding performance conducts the research to the tensile strength, the empirical datum had indicated high tensile steel WH80 was allowed to use in the support design. This topic research initially summarized set of weldings crafts, including the preheating temperature determination, the low intensity match feasibility, the welding speed selection as well as the line energy indeed grades, these research techniques and the method may directly use in the production practice. Has carried on the stress analysis to the support entire frame structural element assembly body, has established the concrete analysis model, regarding outside load processing, the boundary condition determination proposed the concrete processing method, established the integrity support to simplify the structural model. Through the research, we may draw following conclusion: (1) High tensile steel WH80 belongs to the low welding cold crack sensitive steel and may serve as the support design plate. (2) The WH80 steel may select compared to parent metal intensity low welding material J707RH carries on the welding, causes the attachment intensity and the parent metal intensity and so on is strong. (3) Preheating temperature determination besides consideration material chemical composition, but also should consider the crystal to organization's change. For prevents the embrittlement regarding the WH8O high tensile steel, the preheating temperature should designate about 120. (4) The support carries under the operating mode in the top-beam the stress condition to be worst, displays for the support top-beam, Sloping beams, around the connecting rod and the foundation and so on place all has the bigger stress distribution. (5) Highest Von the Mises stress distribution performance for the regional characteristic, the partial existence, in the actual design should consider serves with the high strength plate in this region, but need not the entire frame to use the high strength plate, saves the support cost.
現代煤礦高效工作面的關鍵設備液壓支架 ,是煤礦實現采煤、運輸和支護等所有工序全部機械化的重要環節。結合多年的液壓支架制造經驗 ,分析了液壓支架標準化現狀及弊端 ,進而對液壓支架標準化的實施途徑提出了建議 ,以期對推動液壓支架標準化的進程有所裨益
【英文摘要】 The hydraulic support is the key equipment in today's high production faces underground,it is important tache to realize the mechanisation of all process including mining,transport and shoring etc.Combining years experience of the hydraulic support production,author analysed hydraulic support standardization present situation and abuse,and then made suggestion about the implement channel of hydraulic support standardization,in order to for promote the process of hydraulic support standardization benifit.
在詳細分析液壓支架初撐力與直接頂相互作用機理的基礎上,對支架合理初撐力的確定進行了分析研究,并提出了合理支架初撐力的確定方法。
【英文摘要】 On the basis of analysis of the reciprocity mechanism of original pressure and direct roof, the author analyzes the setting methods of appropriate original pressure of powered support is put forward finally.
綜合分析了國產液壓支架與國外先進國家支架間在技術性能、控制系統、元件制造以及工作介質等諸方面的差異,設計了以插裝閥為控制元件的液壓系統,研究了以水為工作介質的支架液壓元件制造技術。
【英文摘要】 The paper gives a synthetic analysis to the difference between homemade hydraulic timbering and imported one from advanced country on technical properties, control system, parts manufacture and working medium etc., designs the hydraulic system which is used plug-in valve as controlling part and researches the manufacturing technique of hydraulic part in timbering which is working by the medium of water
課題根據當前綜合機械化采煤工作面所采用支護方式暴露出來的問題，提出采用自移式超前支護液壓支架對綜放面端頭進行超前支護；考慮到現今液壓支架生產企業在產品開發過程中存在的種種弊端，提出將虛擬樣機技術應用到液壓支架的設計開發中。在支架投入生產之前在計算機上仿真和修改數字樣機，縮短了研發周期，提高了產品質量，減少了由于制造物理樣機而增加的成本。本課題也為其他機械產品的開發提供了一個成功的范例。
課題介紹了虛擬樣機技術、國內外液壓支架的發展?fàn)顩r以及利用虛擬樣機技術進行自移式超前支架開發的意義；介紹了自移式超前支架的結構特點、承載原理以及應用MATLAB 語言編寫M 文件的方式自動計算出自移式超前支架的主要技術參數；介紹了自移式超前支架液壓控制系統的特點和常用的液壓基本回路，設計出自移式超前支架的液壓控制系統，提出基于虛擬樣機技術的液壓控制系統的實現方法。在UG-NX 環境下完成了自移式超前支架零部件的三維造型設計并采用自底向上的裝配方式，完成了支架的虛擬裝配，查找設計不合理的因素，計算出自移式超前支架的質量、體積、轉動慣量等物理特性，并且完成了從3D 實體模型圖到2D 工程圖的生成。將零部件的3D 模型按照Parasolid 標準輸出“.x_t”文件，為ANSYS 進行有限元分析做準備。介紹了有限元法的基本原理及其求解步驟，在研究CAE技術和CAD技術之間的數據傳輸?shù)幕A(chǔ)上，提出利用ANSYS 和UG-NX 的數據接口UG-NX 環境下輸出的“.x_t”文件導入ANSYS 環境下，進行網格劃分、約束加載求解、后處理，完成自移式超前支架主要承載部件（如頂梁等）的應變、應力分析，根據零部件在承載狀態下變形量的大小驗證零部件的設計是否合理。
關鍵詞：虛擬樣機，自移式超前支架，Parasolid，ANSYS
ABSTRACT
The thesis raises designing the automatic advanced hydraulic bracket to support the
terminal of the working fields according to the problems exposed to the supporting methodnowadays being used in mechanized coal cutting. Considering the hydraulic bracket companyhas many maladies during the development of the products, The thesis raises adopting Virtual Prototyping to design the product. By simulation and modifying digital prototyping oncomputer before product, we can reduce the costs and shorten the design interval and improvethe quality of the products. The theme also provides a successful paradigm for the design ofother machinery products.
The thesis introduces Virtual Prototyping technology, development of the hydraulic
supports and the significance of designing automatic advanced bracket based on VirtualPrototyping technology. The thesis introduces the structure features of the bracket, theprinciple for enduring the load and instructs a method of counting key technology parametersusing MATLAB to edit M files. The features and the fundamental circuit of the hydrauliccontrolling system are also instructed, and the hydraulic controlling system of the automaticadvanced bracket is designed, putting forward the method of emulating based on the VirtualPrototyping technology. The thesis achieves three dimension design for the parts of thebracket, and completes virtual assemble using Bottom-Up assembly, checking irrationalfactors in the design, counting the quality, volume and the retary inertia of the assembly solidand creating engineering drawing from 3D model to 2D view in UG-NX. “.x_t” files of the3D models are exported by Parasolid standard and make ready for the analysis using ANSYSsoftware. The thesis instructs the principle for the FEA and solving steps, put forward themethod of guiding the “.x_t” file into ANSYS conditions based on the investigation of theinterface between the CAE technology and CAD technology, making analysis of stress andstrain for the main loading parts (ef. upper beam, etc) of the automatic advanced bracket bymeshing, loading-solving and postprocessing, and verifying the result of the design of theparts in loading conditions according to the strain.
Keywords：Virtual Prototyping, automatic advanced bracket, Parasolid, ANSYS
II
現代煤礦高效工作面的關鍵設備液壓支架 ,是煤礦實現采煤、運輸和支護等所有工序全部機械化的重要環節。
支撐掩護式支架是以支撐為主 ,掩護為輔的液壓支架 ,用來控制采場頂板下沉斷裂及冒落 ,保證控頂距內頂板完整和必要的回采空間。對支撐掩護式液壓支架的結構特點及合理應用等進行了簡要介紹。為保證支架的合理工作狀態 ,應盡量縮短降架時間 ,快速移架 ,及時支護 ,并保持足夠的支架初撐力在詳細分析液壓支架初撐力與直接頂相互作用機理的基礎上,對支架合理初撐力的確定進行了分析研究,并提出了合理支架初撐力的確定方法。
【英文摘要】The hydraulic support is the key equipment in today's high production faces underground,it is important
Standing shield hydraulic support can control the subsidence,rupture and inbreak of the stope roof,and assure the integrity of the roof and necessary extraction space.The structural feature and its rational application of standing shield hydraulic are introduced in brief.According to the paper,it is necessary to reduce the time of falling support,to move support quickly,to timber the roof in time and keep enough setting pressure. On the basis of analysis of the reciprocity mechanism of original pressure and direct roof, the author analyzes the setting methods of appropriate original pressure of powered support is put forward finally.
收藏