購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖，doc,docx為WORD文檔，有不明白之處，可咨詢QQ:1304139763
骨 輪 注 塑 模 設 計 摘 要 本設計題目為骨輪注塑模設計 體現了側抽芯類塑料零件的設計要求 內容及方 向 有一定的設計意義 通過對該零件模具的設計 進一步加強了設計者注塑模設計 的基礎知識 為設計更復雜的注塑模具做好了鋪墊和吸取了更深刻的經驗 本設計運用塑料成型工藝及模具設計的基礎知識 首先分析了塑件的成分及性能 要求 為選取澆口的類型做好了準備 然后估算了塑件的體積 便于選取注塑機及確 定型腔數量 最后分析了塑件的特征 確定模具的設計參數 設計要點及推出裝置的 選取 在模具設計中采用插入式哈夫塊的側向抽芯機構成型環形外側凹 使模具結構簡單 加工方便本塑件哈夫塊運動與開模方向不一致 所以在脫模時必須考慮設計一個能在 開模時隨著開模過程的進行使哈夫塊分離的裝置 本副模具的設計中 在定模部分設 計安裝了斜導柱 在開模時推件板頂出塑件同時驅動滑塊側分型 直到塑件脫出型腔 這種機構脫?？煽?設計方便且在模具中占用空間較小 非常適合在本副模具中使用 關鍵詞 注塑模 工藝分析 塑件 推板 哈夫塊 骨 輪 注 塑 模 設 計 Abstract The requirement content and direction of the design of the skeleton lastics combinations plastic parts are embodied on this injection mould design of the plastic parts of lateral moving core pulling The designer s foundation knowledge of the injection mould design is reinforced and is able to design more complex injection mould through the design Through the foundation knowledge firstly the composion and the perfourmance of thr part is analyzed to choose the type of the gat advantagely Secondly the volume of the part is estimated to choose the injection molding machine and to detemine the mould quantity conveniencely Lastly the character of the part is analyzed to determine the mould design parameter and design point and choose the ejection assembly This molde design need other side to open on the open molde According to the structure and technology characters of the plastic part with outside annular concave the bayonet Half is used in the injection mould At the open molde the ejector plate ejects the plistic parts at the same time it will made the moving cores move the other side until the plistic parts ejector the cavity this molde ejector is very good because this molde use short area and design easy we often use it Keywords Injection mould process analysis Models Ejector plate the bayonet Half